RGB LED og PIR sensor Jóla

RGB led borði látin flakka milli lita við hreyfingu, annars er rauður sjálfvalin litur.

Síðan þurfti N-chann mosfet til að tengja við arduino og stýra borðanum.

 

Fyrst tengja þetta á breadbord og fá virkni á móti led borða.

ledstrip

Kóði til að flakka á milli lita, fengin frá adafruit.

 

// color swirl! connect an RGB LED to the PWM pins as indicated
// in the #defines
// public domain, enjoy!
 
#define REDPIN 5
#define GREENPIN 6
#define BLUEPIN 3
 
#define FADESPEED 5     // make this higher to slow down
 
void setup() {
  pinMode(REDPIN, OUTPUT);
  pinMode(GREENPIN, OUTPUT);
  pinMode(BLUEPIN, OUTPUT);
}
 
 
void loop() {
  int r, g, b;
 
  // fade from blue to violet
  for (r = 0; r < 256; r++) { 
    analogWrite(REDPIN, r);
    delay(FADESPEED);
  } 
  // fade from violet to red
  for (b = 255; b > 0; b--) { 
    analogWrite(BLUEPIN, b);
    delay(FADESPEED);
  } 
  // fade from red to yellow
  for (g = 0; g < 256; g++) { 
    analogWrite(GREENPIN, g);
    delay(FADESPEED);
  } 
  // fade from yellow to green
  for (r = 255; r > 0; r--) { 
    analogWrite(REDPIN, r);
    delay(FADESPEED);
  } 
  // fade from green to teal
  for (b = 0; b < 256; b++) { 
    analogWrite(BLUEPIN, b);
    delay(FADESPEED);
  } 
  // fade from teal to blue
  for (g = 255; g > 0; g--) { 
    analogWrite(GREENPIN, g);
    delay(FADESPEED);
  } 
}

 

Síðan bæta við PIR sensor.

ledstrippir

 

PIR sensor bætt inn við kóðan og hann fer einn hring og endar í rauðu.

 

int inputPin = 2;               // Ir sensorinn
int pirState = LOW;             // byrja a engri hreyfin
int val = 0;                    // til ad lesa stodu ir

#define REDPIN 5
#define GREENPIN 6
#define BLUEPIN 3
 
#define FADESPEED 5     // make this higher to slow down
 
void setup() {
  pinMode(REDPIN, OUTPUT);
  pinMode(GREENPIN, OUTPUT);
  pinMode(BLUEPIN, OUTPUT);
  pinMode(inputPin, INPUT);     // stilla ir sem input
}
 
 
void loop() {
  val = digitalRead(inputPin);  // lesa gildi á input
  if (val == HIGH){
  int r, g, b;
 
  // fade from blue to violet
  for (r = 0; r < 256; r++) { 
    analogWrite(REDPIN, r);
    delay(FADESPEED);
  } 
  // fade from violet to red
  for (b = 255; b > 0; b--) { 
    analogWrite(BLUEPIN, b);
    delay(FADESPEED);
  } 
  // fade from red to yellow
  for (g = 0; g < 256; g++) { 
    analogWrite(GREENPIN, g);
    delay(FADESPEED);
  } 
  // fade from yellow to green
  for (r = 255; r > 0; r--) { 
    analogWrite(REDPIN, r);
    delay(FADESPEED);
  } 
  // fade from green to teal
  for (b = 0; b < 256; b++) { 
    analogWrite(BLUEPIN, b);
    delay(FADESPEED);
  } 
  // fade from teal to blue
  for (g = 255; g > 0; g--) { 
    analogWrite(GREENPIN, g);
    delay(FADESPEED);
  } 
}
}